Universal trasnmitter 4116

Mô tả

Applications

Linearized, electronic temperature measurement with RTD or TC sensor.

Conversion of linear resistance variation to a standard analog current / voltage signal, i.e. from solenoids and butterfly valves or linear movements with attached potentiometer.

Power supply and signal isolator for 2-wire transmitters. Process control with 2 pairs of potential-free relay contacts and analog output.

Galvanic separation of analog signals and measurement of floating signals.Universal trasnmitter 4116

The 4116 is designed according to strict safety requirements and is therefore suitable for application in SIL 2 installations.

Suitable for the use in systems up to Performance Level “d” according to ISO-13849.

 

Technical characteristics Universal trasnmitter 4116

When 4116 is used in combination with the 45xx display / programming units, all operational parameters can be modified to suit any application. As the 4116 is designed with electronic hardware switches, it is not necessary to open the device for setting of DIP-switches.Universal trasnmitter 4116

A green / red front LED indicates normal operation and malfunction. A yellow LED is ON for each active output relay.

Continuous check of vital stored data for safety reasons.
4-port 2.3 kVAC galvanic isolation.Universal trasnmitter 4116

Mounting / installation / programming

Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.

Configuration, monitoring, 2-point process calibration andmore are accomplished using PR’s 45xx detachable displays.

All programming can be password-protected. Universal trasnmitter 4116

Environmental Conditions
Operating temperature…………………………….. -20°C to +60°C
Storage temperature……………………………….. -20°C to +85°C
Calibration temperature…………………………… 20…28°C
Relative humidity…………………………………….. < 95% RH (non-cond.)
Protection degree……………………………………. IP20
Mechanical specifications
Dimensions (HxWxD)………………………………. 109 x 23.5 x 104 mm
Dimensions (HxWxD) w/ 4501/451x………….. 109 x 23.5 x 116 / 131 mm
Weight approx………………………………………… 175 g
Weight incl. 4501 / 451x (approx.)…………….. 190 g / 205 g
Wire size……………………………………………….. 0.13…2.08 mm2 AWG 26…14
stranded wire
Screw terminal torque……………………………… 0.5 Nm
Vibration………………………………………………… IEC 60068-2-6
2…13.2 Hz……………………………………………… ±1 mm
13.2…100 Hz………………………………………….. ±0.7 g
Common specifications
Supply Universal trasnmitter 4116
Supply voltage, universal…………………………. 21.6…253 VAC, 50…60 Hz or
19.2…300 VDC
Fuse……………………………………………………… 400 mA SB / 250 VAC
Max. required power……………………………….. ≤ 2.5 W
Max. power dissipation……………………………. ≤ 2.5 W
Isolation voltage
Test voltage……………………………………………. 2.3 kVAC
Working voltage……………………………………… 250 VAC (reinforced) / 500
VAC (basic)
Response time
Temperature input (0…90%,
100…10%)……………………………………………… ≤ 1 s
mA / V input (0…90%, 100…10%)……………… ≤ 400 ms
Auxiliary supplies
2-w. supply (term. 44…43)……………………….. 25…16 VDC / 0…20 mA
Programming…………………………………………. PR 45xx
Signal dynamics, input…………………………….. 24 bit
Signal dynamics, output…………………………… 16 bit
Signal / noise ratio………………………………….. Min. 60 dB (0…100 kHz)
Accuracy……………………………………………….. Better than 0.1% of sel. range
EMC immunity influence.Universal trasnmitter 4116………………………… < ±0.5% of span
Extended EMC immunity: NAMUR
NE21, A criterion, burst……………………………. < ±1% of span
Input specifications
RTD input
RTD type……………………………………………….. Pt10/20/50/100/200/250;
Pt300/400/500/1000;
Ni50/100/120/1000;
Cu10/20/50/100
Cable resistance per wire………………………… 50 Ω (max.)
Sensor current……………………………………….. Nom. 0.2 mA
Effect of sensor cable resistance
(3-/4-wire)………………………………………………. < 0.002 Ω / Ω
Sensor error detection…………………………….. Yes
Short circuit detection……………………………… < 15 Ω
Linear resistance input
Linear resistance min….max…………………….. 0 Ω…10000 Ω
Potentiometer input
Potentiometer min….max…………………………. 10 Ω…100 kΩ
TC input
Thermocouple type…………………………………. B, E, J, K, L, N, R, S, T, U,
W3, W5, LR
Cold junction compensation
(CJC) via ext. sensor in
5910……………………………………………………… 20…28°C ≤ ±1°C, -20…20°C /
28…70°C ≤ 2°C
CJC via int. mounted sensor…………………….. ±(2.0°C + 0.4°C * Δt)
Sensor error detection…………………………….. Yes
Sensor error current: When
detecting / else……………………………………….. Nom. 2 μA / 0 μA
Current input
Measurement range………………………………… 0…23 mA
Programmable measurement ranges………… 0…20 and 4…20 mA
Input resistance.Universal trasnmitter 4116……………………………………… Nom. 20 Ω + PTC 50 Ω
Sensor error detection: Loop
break 4…20 mA………………………………………. Yes
Voltage input
Measurement range………………………………… 0…12 VDC
Programmable measurement ranges………… 0/0.2…1, 0/1…5, 0/2…10 VDC
Input resistance………………………………………. Nom. 10 MΩ
Output specifications
Current output
Signal range…………………………………………… 0…23 mA
Programmable signal ranges……………………. 0…20/4…20/20…0/20…4 mA
Load (@ current output)…………………………… ≤ 800 Ω
Load stability………………………………………….. ≤ 0.01% of span / 100 Ω
Sensor error indication…………………………….. 0 / 3.5 / 23 mA / none
NAMUR NE43 Upscale/Downscale…………… 23 mA / 3.5 mA
Output limitation, on 4…20
and 20…4 mA signals……………………………… 3.8…20.5 mA
Output limitation, on 0…20
and 20…0 mA signals……………………………… 0…20.5 mA
Current limit.Universal trasnmitter 4116…………………………………………… ≤ 28 mA
Voltage output
Signal range…………………………………………… 0…10 VDC
Programmable signal ranges……………………. 0/0.2…1; 0/1…5 ; 0/2…10;
1…0.2/0; 5…1/0; 10…2/0 V
Load (@ voltage output)………………………….. ≥ 500 kΩ
Relay output
Relay functions………………………………………. Setpoint, Window, Sensor
error, Latch, Power and Off
Max. voltage…………………………………………… 250 VAC / VDC
Max. current…………………………………………… 2 A
Max. AC power………………………………………. 500 VA
Max. DC current, resistive
load > 30 VDC………………………………………… See manual for details
Observed authority requirements
EMC……………………………………………………… 2014/30/EU
LVD………………………………………………………. 2014/35/EU
RoHS…………………………………………………….. 2011/65/EU
EAC………………………………………………………. TR-CU 020/2011
ApprovalsUniversal trasnmitter 4116
c UL us, UL 508……………………………………… E231911
FM………………………………………………………… 3025177
DNV-GL Marine……………………………………… TAA0000101
EU RO Mutual Recognition Type
Approval………………………………………………… MRA000000Z

Công ty TNHH ADOPA

Địa chỉ: Số 18 Thạnh Xuân 43, phường Thạnh Xuân, Quận 12, Tp Hồ Chí Minh

Hotline: 0968 02 1386

Email: infoadopa@gmail.com

Xin hân hạnh được phục vụ quý khách!